Advanced Pulse Width Modulation (PWM) on Nordic nRF52 Series

In this blog, I would like to describe more details how to use the PWM module on Nordic nRF52 Series MCU. Basically, nRF52 has started to support hardware PWM modules. If someone would like to generate some complicated duty cycle or waveform, it is better to know how to use the PWM module inside nRF52.

PWM – Pulse Width Modulation

The PWM module enables the generation of pulse width modulated signals on GPIO. The module implements an up or up-and-down counter with four PWM channels that drive assigned GPIOs.

PWM Individual ChannelTotal Channel
nRF5281014
nRF5281114
nRF52832312
nRF52833416
nRF52840416

For example, nRF52832 has 3 PWM individual channel. Those modules provide up to 12 PWM channels with individual frequency control in groups of up to four channels. Furthermore, a built-in decoder and EasyDMA capabilities make it possible to manipulate the PWM duty cycles without CPU intervention. Arbitrary duty-cycle sequences are read from Data RAM and can be chained to implement ping-pong buffering or repeated into complex loops.

The maximum of the PWM base clock frequency is 16MHz. It means that it can only have a PWM frequency in integers of MHz, ie, 1, 2, 3, 4… MHz. 

Listed here are the main features of one PWM module:

  • Fixed PWM base frequency with programmable clock divider
  • Up to four PWM channels with individual polarity and duty-cycle values
  • Edge or center-aligned pulses across PWM channels
  • Multiple duty-cycle arrays (sequences) defined in Data RAM
  • Autonomous and glitch-free update of duty cycle values directly from memory through EasyDMA
  • Change of polarity, duty-cycle, and base frequency possibly on every PWM period
  • Data RAM sequences can be repeated or connected into loops
PWM Module

All the details of the PWM specification can be found at

https://infocenter.nordicsemi.com/topic/ps_nrf52840/pwm.html

Wave Counter

The wave counter is responsible for generating the pulses at a duty-cycle that depends on the compare values, and at a frequency that depends on COUNTERTOP. There is one common 15-bit counter with four compare channels. Thus, all four channels will share the same period (PWM frequency), but can have individual duty-cycle and polarity. The polarity is set by the value read from RAM, while the MODE register controls if the counter counts up, or up and down. The timer top value is controlled by the COUNTERTOP register. This register value in conjunction with the selected PRESCALER of the PWM_CLK will result in a given PWM period. A COUNTERTOP value smaller than the compare setting will result in a state where no PWM edges are generated. Respectively, OUT[n] is held high, given that the polarity is set to FallingEdge.

All the compare registers are internal and can only be configured through the decoder presented later.

By using the wave counter, basically it can generate two difference waveforms.

  • Edge align mode
  • Center align mode

For example, I would like to generate the duty cycle as

The period = 1 / 1MHz * 500 * 2 = 1ms (because top value = 500)

  • The value of the COMP1 is 300. (40% duty cycle)
  • The value of the COMP2 is 250. (50% duty cycle)
  • where 0x8000 is the pin polarity

Complex Sequence Waveform

nRF52 can support complex sequency wavaform which plays from the Data RAM through DMA.

Decoder with EasyDMA

The decoder uses EasyDMA to take PWM parameters stored in RAM and update the internal compare registers of the wave counter, based on the mode of operation.

The DECODER register controls how the RAM content is interpreted and loaded into the internal compare registers. The LOAD field controls if the RAM values are loaded to all compare channels, or to update a group or all channels with individual values. The following figure illustrates how parameters stored in RAM are organized and routed to various compare channels in different modes:

Nordic Thingy 52 provides an demo how to use the PWM to play the low quality sound.

Nordic Thingy 52

Nordic Thingy:52 is an easy-to-use development platform, designed to help you build IoT prototypes and demos, without the need to build hardware or write firmware from scratch.

Sound Service

The Sound service lets you control Thingy’s microphone (iOS and Android) and speaker. The Thingy Sound service is based on two building blocks, the speaker and the microphone, which can work in specific modes.

Speaker modes:

  • 8-bit PCM (streaming)
  • Frequency and duration (piano keyboard)
  • Sample (sample sound effects)

Inside the Thingy52 Schematics,

Firmware of the Thingy52

The firmware can be download at

https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms/Nordic-Thingy-52/Download

Documentation of the Nordic Thingy52

https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/index.html

How to play the complex sound

  • It is using the nrf_drv_pwm driver which is similar to the nrfx_pwm (after Nordic SDK 15.0 or later)

If you have any comments, welcome to leave here.

2 thoughts on “Advanced Pulse Width Modulation (PWM) on Nordic nRF52 Series

  1. I had emailed Jimmy few times without getting any response. Now I realized this blog isn’t well maintained. These posts are just short snippets from Product Specification PDF. Reading the PDF is more useful.

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.